Add a Gibertini 1.5m dish, polar mount, 18-inch actuator, Titanium LNB, V Box
Order code AD15M36
Only £499.95

System option. Add a 76mm 1m high ground stand to this system. Discounted price.
To buy this ground stand on it's own (not with a system) go to the ground stand page
Order code OPTGR76
£124.95

Add a heavy duty Andrews 1.8m
polar mount dish kit to my receiver,
heavy duty actuator & Andrews matched
feedhorn with C120 0.3dB Inverto LNB





Channel Master 1.8m dish. Very high gain one piece proven design. This motor unit is
exclusive to the Satellite Superstore. Polar mount with aluminum adapter to fit Andrews
(Channel Master) 1.8m dish. Designed and built by the Satellite Superstore.
The polar mount picture above shows a standard 12 inch actuator but we include the HEAVY DUTY
18 inch actuator (also shown above) with this polar mount, - not the standard 12 inch.
The heavy duty actuator is, longer, thicker and much stronger.
The light-weigh (but very strong) aluminum adapter bracket fits onto the back of the Andrews
1.8m dish. The adapter bracket is made of unequal box and uses aluminum welding with bracing
gussets. This gives maximum strength combined with lightness. The lightness puts less strain
on the polar mount. The complete motor kit is available sepately on our motors page
The polar mount collar fits a 3 inch (76mm) pole or ground stand.



Andrews (Channel Master) feedhorn. Highly recommended for Channel Master 1.8m dishes.
Using this feedhorn with a C120 flange LNB provides better matching & higher gain than a 40mm clamp LNB of
equivalent noise level. Why buy a high quality Channel Master dish and use a compromise
40mm mass market LNB where the feed is made for ANY dish?
Taking a 1.8m dish as an example. A 40mm LNB may only illuminate 1.7m of dish area or perhaps 1.9m of dish area
(i.e. including noise round the edges) But with a matched feedhorn, exactly 1.8m of dish area is illuminated.
High output 0.3dB C120 Inverto LNB included (good for longer cable runs.) The highest gain 1.8m dish on the market.
(Has more gain than many 2.4m dishes) An ultimate system for enthusiasts. V Box included.
UPDATE 2008. Continued improvements in the polar mount design. The bar between the actuator end and the
mount has now been upgraded to heavier, stiffer steel angle improving rigidity. (Not shown in earlier picture
above but the strengthened support arm is shown in a new picture to the right of the LNB.)
Free fitting kit with detailed instructions included with all full motorised systems included.
It is worthwhile checking out our support page page (especially if you plan to do the fitting yourself)
Shipping options. Discounted shipping on all web orders.
UK - When you add a this dish kit to your receiver choice, mainland UK delivery is still included in the price,
so choose "Mainland UK delivery included" - UK shipping option No 1.
Or for "UK offshore islands (and Eire) by courier" - oversized delivery - quote by e-mail (or ring us).
All internationals - Within the EU or outside of the EU - choose the "International quote by e-mail" shipping option.
Note that to most international EU destinations (including Eire,) delivery is about £225.00
Order code AD18M36
Add £1179.95

Option - Ground Stand for the
1.8m motorised Andrews dish





Manufactured by the Satellite Superstore. This is our own stand. It is 1.25m high and uses a
76mm (3.0") pole. Heavy 6mm thick angle is used along the base and the angle dimensions are 60mm by 60mm.
There are 12 holes for fixing down to concrete or paving. 4 in each angle. See bottom right picture.
It is etch-primed and pained black. The final coat of paint is baked in an oven dried.
The stand is bolted together to make it easy to ship. A fully welded stand of this size could not
be transported with a courier and would need a (expensive) haulage company, so this stand bolts
together. Multiple bolts are used for maximim rigidity. The stand is heavy but it needs to be.
This stand is designed for our motorised version of the 1.8m Andrews dish.
Discounted price when you buy the 1.8m motorised dish kit.

Dish option. Ground Stand for the 1.8m Andrews dish. 76mm (3.0-inch) diameter pole
Order code OPT18GM
£299.95

Option. Adjustanble feet for motorised use.



This is an option (discounted price) when ordering a 76mm (3-inch) ground stand.
Feet are not included with the stand above. (To buy the feet without a ground stand see above.)
With the 1.8m stand above, for motorised use, to make the pole plumb, we would recommend at least 6 feet
and preferable 9 although up to 12 can be used. It will therefore be necessary to add this option more than once.
Manufactured by the Satellite Superstore. An exclusive high quality product.
Order code 3EXTRAF
Add £20.00

Buying a fully loaded (programmed)
satellite receiver for motorised use.

This service is available for any motorised dish. If you are buying a system, or just a receiver
and you already have a motorised dish, we can take the receiver out of its box and fully program
it on one of our demonstration dishes. This would mean that the new programmed receiver can be
connected up by the customer and all the satellites channels will work straight away.
(Providing it is connected to a dish that is properly fitted, set up, and tracking the arc)
It would take a customer about many hours to program a receiver (since there would be
unfamiliarity with the installation menu system). After programming, the channels are then organised
in a logical order. (This is what takes the most time.) We make sure the first channel on every
satellite is a clear free to air unscrambled channel. Channels are organised into a logical order.
e.g. Adult channels all together etc. Movie packages .. etc. Moving all of the channels into a
logical order can take days. This programming is ONLY £19.95 This service is entirely optional
but for mail order customers it can take a great deal of the worry and uncertainty out of a
purchase. The programmed receiver is supplied without dish positions to be used with any dish.
Only the positions and the limits need to be added. This is a 10 minute job. This option is
ideal if you are buying a full motorised system and you intend to fit it yourself.
This option helps a great deal. It also makes it easier to install a motorised dish as channels
already loaded can help identify the satellite if a budget satellite meter is being used. Detailed
installation notes written by us are included and we can talk you through the installation
over the phone if required. See our support package on our support page.
Our notes guide you through how to connect a programmed receiver, and setting the positions.
In addition, useful easy to follow notes on blind searching written by us are included for
future reference. For international orders, this option has one other worthwhile purpose.
The receiver is fully tested before shipping while it is being programmed.
Motorised receiver full programming option
Order code MOTPROG
Add only £19.95