Primesat 1.8m inclined orbit motorised
dish, matched feedhorn & c120 flange LNB.
Ku band or / and C Band LNB options
Primesat 1.8m dish with inclined orbit polar mount using two actuators
The 18 inch
heavy duty actuator can go on either side for moving east and west. The 12 inch
actuator is for up and down adjustment.
This is ideal for tracking inclined orbit satellites. Two positioners are needed. These can be a Primesat PR1000 V Box
east and west using a modern HD satellite receiver in automatic mode or in manual mode and up and down using the
positioner. Manual mode would be by using the handsets which came with the positioners.
All satellite positions can be stored in the V Box with control from the satellite receiver and up and down positions can be
stored in the EZ2000. For inclined orbit satellites a timing chart is useful but ring
us for further advice on this subject.
In the early days of satellite most dishes were prime focus. These days most dishes are offset. It is two ways of doing the same
job but prime focus dishes point upwards and look purposeful. From the appearance point of view they are usually the enthusiast
favourite. This one is made of aluminium and is one piece. (As a general rule, aluminium is preferable to steel and 1-piece tends
to be more efficient that "petalised" or segments.) This attractive dish comes complete with a very heavy duty polar mount, a
prime focus matched feedhorn and Inverto c120 flange LNB. This dish fits on a 76cm diameter pole. The polar mount
is "dipped galvanised" which is the best possible type of treatment for withstanding corrosion in high salt areas. Everything
about this dish is high quality. All of the nuts and bolts are made of stainless steel except the main elevation adjuster which
is made of brass. More information
. More pictures
. A standard
(not inclined orbit) version of this dish is available.
Technical - F/D Ratio - 0.41, Gain @ 10.95 GHz 44.8 dB, Gain @ 11.70 GHz 45.6 dB, Gain @ 12.70 GHz 46.4 dB
This heavy duty polar mount comes complete with a quality genuine heavy duty
Superjack 18" actuator
Superjack 12" actuator
. Using a Diseqc receiver, an optional V Box
is also needed. This converts Diseqc commands
to 36-volt positioning and is fully automatic. it also introduces more power to drive the heavy duty 36 volt motor east and
west. A discounted V box option and a discounted EZ2000 positioner is available below.
A suitable stand for the 1.8m dish is a
1.25m high 76mm diameter pole ground stand is on our ground stands
page, but a discounted ground stand
is available below.
These dishes are available with a single, twin, quad, or quatro LNB (see below
). There is also a C Band LNBF option, a
Ku band and C band LNBF option and a dual polarity LNBs option (see below
). 4 core motor control cable
motors is available. If you live in an area that receives regular snowfall, you may be interested in a satellite dish heater
Free UK mainland UK delivery to most post codes. (There may be additional charges to Scottish highlands)
so choose "Free UK mainland delivery
" - UK shipping option No 1.
Or for UK offshore islands (and Eire) by courier - oversized delivery - quote by e-mail (or ring
All internationals - Within the EU or outside of the EU - choose the "International quote by e-mail" shipping option (or ring
Options- Primesat C Band (C & Ku) 60mm boss, feedhorn, LNBF kits
Change the Primesat feedhorn and c120 LNB for a C Band, C and Ku band, or dual polarity feedhorn and LNB kit. Note. The feed
support boss on the dish is changed from 23mm - 40mm to 23mm - 60mm and so fitting a 60mm C band feedhorn is not a problem.
Options - Change to a Primesat C Band and Ku band LNB option.
Order code OPTCKUPG
Add only £90.00
Dish option - Change to a Primesat dual Polarity C Band feedhorn with
two C Band CPR229 flange block type LNBs.
Order code OPDP2LNB
Add only £165.00
Dish option - Change to a Primesat quad C Band voltage switching 13K LNBF.
Order code OPT4CLNB
Add only £60.00
Option - Ground stand for the 1.8m motorised Primesat dish
Manufactured by the Satellite Superstore. This is our own stand. It is 1.25m high and uses a 76mm (3.0") pole. Heavy
6mm thick angle is used along the base and the angle dimensions are 60mm by 60mm. There are 12 holes for fixing down
to concrete or paving. 4 in each angle. See bottom left picture. It is etch-primed and pained black. The final coat
of paint is baked in an oven for a hard finish. The stand is bolted together to make it easy to ship. Multiple bolts
are used for maximum rigidity. The stand is heavy but it needs to be. This stand is designed for our motorised
version of the 1.8m Primesat dish. This stand is at a discounted price when you buy it with the 1.8m motorised dish kit.
Option - Ground stand for the 1.8m Primesat dish. 76mm (3.0-inch) diameter pole
Our own "Primesat Vision" heavy duty range. Manufactured since 1991.
Discounted ground stand option when you buy a 1.8m Primesat dish. To buy this stand separately go to the Ground Stands
Order code OPT18GM
Add only £299.95
Option - Adjustable feet for motorised use. (discounted)
This is a worthwhile option (discounted price) when ordering a 76mm (3-inch) ground stand. Feet are not included as
standard with the stand above. Using the 1.8m stand above, for motorised use, to make the pole plumb, we would
recommend at least 6 feet and preferable 9 although up to 12 can be used. It will therefore be necessary to add
this option more than once. Manufactured by the Satellite Superstore. An exclusive high quality product.
Option - Adjustable feet for motorised use.
Our own "Primesat Vision" heavy duty range. Manufactured since 1991.
Discounted adjustable feet option when you buy a 1.8m Primesat dish. To buy these feet separately go to the Ground Stands
Order code EXTRAF3
Add only £30.00 for 3 feet
Primesat 7680 Shim.
If you are using your own 76mm pole for the Primesat dish and you are not buying our ground stand option you will need
this spacer. If you are buying our ground stand option with the Primesat dish, the shim is included
. More Information
Order code 7680SPA
See our other web site at-
This site includes many products that are exclusive to the Satellite Superstore.
The site contains -
• Products that we manufacture (e.g. We have manufactured heavy duty wall mounts and ground stands since 1991).
• Selected products which have our own Primesat brand name and have been prepared to our specifications.
• Selected products where we have been appointed the authorised UK or European distributor by the manufacturer.
is an information site. Here you will find full specifications and many detailed pictures.
To buy any of these products, simply order them on this web site.
Link to our own satellite museum site
Satellite Museum. A Museum of vintage satellite receivers.
For old Satellite receivers with knobs on and the history of satellite TV.
Also see www.rewindmuseum.com
. A Museum of vintage consumer electronics.
Vintage reel to reel video recorders. Vintage VHS and Betamax VCRs. Vintage video cameras. Vintage
Laser Disc. Vintage Computers. Old telephones. Old brick mobile phones. Vintage Hi Fi, Old reel
to reel audio and early audio cassette decks. Including, the history time line of vintage
consumer electronics ... and much more .....
It is well worth a visit.
Only The Satellite Superstore brings you
great products, advice and it's own museum.
You may be interested in two other web sites.
This web site shows all of the restoration process and the modifications to this truck.
In addition, there is a hard high quality tonneau cover on a new web site
at www.classictonneaucover.com for the 1947-53 Chevy truck.
Unlike many other companies we are happy to answer questions on the phone.
Tel. (UK) 01207 544664 and 01207
International Tel. + 44 1207 544664.
If you are ringing us about a product you have already purchased, you should ring the support line on your invoice.
Before sending questions via e-mail please check-out our Frequently asked questions
this could save
If you have any questions & comments regarding this site's content, or you need advice please ....
click here to go to our contact forms
Copyright © 2017 Vision International. All rights reserved.